Servicing · AMC · Panel Manufacturing
UltraBright Electrical and Services maintains and repairs BMS electrical equipment, and manufactures custom electrical panels built to your load and your site. Fast response, clean workmanship, and engineers who know the equipment they are standing in front of.
What We Do
Most electrical failures announce themselves weeks in advance — in a thermal scan, a rising harmonic, a relay that trips a little too often. We find them while they are still cheap.
Inspection, calibration and repair of the field devices and controllers your building management system depends on.
Custom electrical panels designed, fabricated, wired and routine-tested in house to your single-line diagram.
Scheduled preventive maintenance with a defined SLA, so problems surface on your calendar rather than at 2am.
Supply and installation of new equipment, and upgrades to switchgear that has reached the end of its life.
Panel Manufacturing
Every panel is routine-tested and supplied with its test report, GA drawing and wiring schedule.
Main distribution boards and LT main switchboards, with incoming and outgoing protection to your specification.
DistributionMotor control centres and power control centres for process and utility plant, with starters and protection built in.
ControlAutomatic power factor correction panels to cut penalty charges and ease load on your distribution system.
Power FactorFloor and zone level distribution boards, built to match the main panel and labelled for maintenance.
DistributionPLC-based control panels with the field wiring, interlocks and HMI integration your process needs.
AutomationAuto Mains Failure panels that sense a supply outage, start the DG set and transfer load automatically — then hand back when mains returns.
BackupWeatherproof low-tension kiosks for incoming supply control where there is no indoor substation room.
OutdoorPurpose-built control panels for HVAC plant, pump sets and lighting, wired to your control philosophy.
ControlMetering panels and automatic/manual changeover panels for reliable supply switching and accurate billing data.
MeteringBuild Standard
Panels are designed and fabricated to IS/IEC 61439 and IS 8623. Every board is routine-tested and handed over with its report.
| System voltage | 415 V, 3-phase, 4-wire, 50 Hz |
|---|---|
| Rated current | Up to 6300 A |
| Short-circuit withstand | Up to 50 kA for 1 second |
| Degree of protection | IP42 / IP54 / IP55 indoor · IP65 outdoor |
| Form of separation | Form 1 to Form 4b |
| Busbar | Electrolytic copper or aluminium, sleeved |
| Enclosure | CRCA sheet steel, 1.6 mm / 2.0 mm |
| Finish | Seven-tank pre-treatment, powder coated |
| Standards | IS/IEC 61439-1 & 61439-2, IS 8623 |
Add your ISO certificate, electrical contractor licence number and any type-test reports here. Buyers look for this first.
Live Demonstration
This is a simulation, not live site data — but it is the shape of what a BMS gives you. Hover a system to see what it touches.
Chilled water · 2 AHUs
Zones occupied
Incomer load · PF 0.98
All zones normal
Who We Work With
How We Work
No stage starts before the one before it is signed off. You get a document at every handover, not a phone call six weeks later.
We walk the site, list what is installed, thermal-scan the existing boards and tell you what condition it is really in.
Condition reportSingle-line diagram, GA drawing and a priced scope. No provisional sums that quietly grow later.
Drawings + fixed quoteFabrication, busbar work and control wiring on our floor, then routine testing before anything is loaded onto a truck.
Routine test reportInstallation scheduled around your operations, terminated, meggered and commissioned with your team present.
Commissioning sheetPlanned preventive visits under AMC, with a written report after each one and a response time you can hold us to.
Service recordsAbout Us
UltraBright Electrical and Services works at both ends of the same problem. We service and maintain the BMS electrical equipment already installed in your building, and we manufacture the panels that replace it when it is time.
Because we do both, our panels are built the way a service engineer wishes they had been built — accessible, properly labelled, and easy to work on at three in the morning.
Talk to UsCommon Questions
Clients on an annual maintenance contract get a committed response window written into the agreement. For everyone else we attend as soon as a crew is free — call us and we will tell you honestly when that is.
Yes. Most of our servicing work is on panels and BMS equipment installed by somebody else. We will survey what is there and tell you what it needs.
It depends on the rating and on component lead times. Once the GA drawing is approved, a typical distribution board is a matter of weeks. We give you a date at quotation stage and tell you early if it moves.
The panel, its routine test report, the approved GA drawing and the wiring schedule. Everything is labelled so whoever maintains it next is not guessing.
Often that is the only sensible time. Shutdowns on live sites are usually planned for nights or weekends, and we schedule around your operations.
Contact
